How To Wire A Winch Switch? – 4 Easy Methods In 2023

The Winch Switch needs to be wired accurately to make the winch work properly. You will need power for the winch, switch, and receiver.

Connect the black wire to the battery positive terminal (red wire to negative terminal) and connect the white wire to the switch ground terminal.

Connect red and green wires to the receiver ground terminal.

Install the switch in the desired location. Connect the power to the winch and check to make sure it works properly.

If not, consult your winching manual for further instructions because there could be some extra wiring, but usually, this is a complex process of wiring a winch switch.

Best Four Types For Winch Wiring

1. How To Wire A ATV Winch Switch:

ATV winch switches can be wired in a couple of ways. The first way is to use an inline switch and the second way is to use a remote switch.

If using an inline switch, connect the black wire to the battery positive terminal and the white wire to the switch ground terminal.

Connect the red and green wires to the receiver ground terminal.

If using a remote switch, connect the black wire to the battery positive terminal and the white wire to the switch ground terminal.

Connect the red and green wires to the receiver ground terminal.

2. How To Wire SUVs Winch switch

To wire SUVs winch switch, you will need to connect the black wire to the battery positive terminal and the white wire to the switch ground terminal.

Connect the red and green wires to the receiver ground terminal.

3. How To Wire Remote Winch Switch

Remote winch switches are more complicated to wire because they have some extra wiring work.

First, connect the black wire to the battery positive terminal to wire it up. Connect the white wire to the switch ground terminal.

Next, connect the red and green wires to the receiver ground terminal.

Please make sure the wires are long enough to reach the switch without stretching them too much.

Finally, connect the black and white wires of the remote switch.

This will activate the switch. Please make sure the switch is correctly aligned before you plug it in.

Wire Winch Power Switch:

Winch Power switches are more complicated to wire because they need two separate circuits.

The first circuit is for the winch power, and the second is for the remote switch.

Rest the process is the same as wiring a remote winch switch. You only have to follow all the steps for both switches.

4. How To Wire A mic tuning Winch Switch

Mictuning winch switches are used to control the mictuning winch.

To wire it up, connect the black and white wire respectively and then connect the other two wires to the ignition wire.

Please make sure the black and white wires are long enough to reach the switch without having to stretch them too much.

Remote winch switches are used to control the mictuning winches from a distance.

So, there will be two extra wires if you are using a remote control winch which will also need to be connected with a remote switch button, same as a power switch.

What If Your Wiring Doesn’t work:

If your wiring does not work, a few things can be checked:

1. Ensure all of the wires are correctly connected and long enough to reach the switch without stretching them too much.
2. Please make sure the switch is correctly aligned before plugging it in.
3. If everything else checks out and the wiring still does not work, it may be necessary to replace the switch.

1. Rocker Switch:

Rocker switches are used to control the speed of the winch.

To wire it up, first, connect one black wire to the power terminal and one white wire to the neutral terminal.

Then connect the other two wires to the rocker switch, and that’s all you have to do to take on the rocker switch onboard.

2. How To Test A Winch Switch

To test a winch switch, first, make sure the power is turned on to the winch.

Then, manually move the switch to the desired position. If the switch works, your wiring is correct, and you can move on to the next step.

If the switch does not work, there may be a problem with the switch or with the wiring. In this case, it may be necessary to replace the switch.

3. How To Fix A Winch Switch

If the switch does not work, it may be necessary to replace it.

To replace the switch, first, disconnect the wires from the old switch and connect them to the new switch.

Then, reattach the cover and screws.

If the switch works but does not turn the winch, it may be necessary to adjust the cable tension.

Loosen the cable clamp and pull the cable until it is slightly tight.

Reattach the clamp and check to make sure the winch turns. If not, loosen the cable further and reattach the clamp again. Finally, tighten the cable as needed.

If the switch does not work and the winch turns when the lever is pulled, replacing the cable or switch may be necessary.

Conclusion:

Wiring a winch is a piece of cake if you know how to connect the wire accurately.

The most common issue with a winch switch is that the cable is not tight enough, so make sure to adjust it as needed.

If the switch does not work, you may have to replace it. The process is the same either way.

So, wire your winch switch with ease, and to make it work correctly, follow all the mentioned steps.

Video Guide: